I was born a hunter and have spent most of my life in the field in pursuit of game. I have hunted with every make and model of rifle common and uncommon in the industry. I tend to bring a unique perspective on hunting and long-range rifles because that has become my passion.
I can build guns from the ground up, focusing mostly on bolt action rifles. I have a simple philosophy on pricing, if you want a gun to shoot under an inch and are happy with that than the bill will only be $400 plus materials. If you want a gun to shoot under half an inch then the bill be $600 plus materials. If you have to have the rifle that shoots better than you do and can print a group into the quarter inch range and you'll pay me $800 plus materials to do that Then I will work my tail off to get you past the .25MOA mark. Typically I don't take any AR platforms into the quarter inch range, but I have produced many half MOA rifles on the AR platform
1 MOA= $400.00 + Materials
.5 MOA= $600.00 + Materials
.25 MOA= $800.00 + Materials
These prices include a custom Dura-Coating to the clients specification.
Now does this not seem fair?
If I do not accomplish the MOA that you are looking for then you will not pay for that MOA. If your rifle only shoots to a .30 and you were hoping for .25 then you will only pay the bill on a .5 inch gun. I will shoot all groups and have them witnessed, if you like, and they will be measured center to center by a third party.
Most of what I do:
I do allot of work on existing rifles that simply do not shoot. I always start by floating the barrel, bedding and or pillar bedding the action, servicing and tuning the trigger, if possible, or i will flat out install a new trigger on your rifle, I may even hand Lap the barrel if that is what it takes. I will then develop load data based on known bullets (burger, sierra, RG Henson) and will make sure that the work we did meets your accuracy goals for the project.
I will provide you a proof target, as well as load data and conditions the proof was shot under. With this information and the Drop cards that I work up for your individual rifle you will be set to do things with a gun the likes of which you have only seen on TV. This will give all my clients the absolute knowledge that their gun shoots, and will shoot, just as they expect it to every time they pull the trigger If you are not a handloader, do not worry, I will also set up a file for you and your specific rifle and load with Superior Ammunition, and they will be happy to provide you with custom loaded ammo that are just for your rifle.
Buyers assistance program.
I can also assist you in the purchase of your next rifle, in the configuration that you desire, and ensure that it is what you expect it to be when you get it. This may include setting the gun up with a scope and rings and basses or even a bi-pod and sling. In today’s market of mass produced products most of the large manufactures of American fire arms have occasional (to be kind) slips in production and quality control. I inspect every gun that comes into my hands. If it is new and not right, I will get one that is right! I will not pass along junk even if it is new junk, no matter what name is stamped on the barrel. I do not do this for free however, and expect to be compensated for my time and shipping. Usually two hundred bucks will keep me happy. Not only that but if I think we can do better for you with a rifle that is used and cheaper I will recommend that to you and give you the option to save some money. Some of the best rifles out there are ones that have already been shot, and have a known pedigree, and I can make even the worst looking gun on the shelf look like brand new, with just a bit of tender loving care, and a whole ton of hard work.
Our list of preferred providers
I Cannot say enough about the quality of this production action, it is engineered to perfection. CZ combined with Schneider Barrels are hard to beat for top accuracy and unbeatable reliability.
You will not find Gary on the web, but he is one of the top 5 barrel makers in the world today, in my opinion and you can read about him and who uses his barrels all over the web. If I could I would only use Schneider barrels.
These are some of the finest scopes in some of the best configurations available in the US at a reasonable price. You can spend two, maybe even three, times as much money on another optic, but the smart money is in the Vortex.
I have now had the pleasure of shooting Nightforce scopes under some of the harshest conditions on the planet and I must say that they are, bar-none, one of the best values for money as optics go. It is more than likely that your children's children will be shooting your Nightforce long after you are gone.
I also run a full service Dura-Coating process that can transform any rifle into a thing of beauty. Contact me for pricing and for availability. All patterns are hand laid so that no two are alike. Each coating is a one time one off project and you will never have another rifle that looks like yours does.
$175.00 to $225.00